XIZUMINT.tlk Driver Reference
Izumi FA-1/1J/2/2J Network Protocol Driver
This driver requires that you have TAS-HMITalk 8.04 installed.
XIZUMINT driver allows you to connect to IDEC IZUMI Corp. FA-1J/FA-2/
FA-2J Series equipment on a network basis.
(There is another limited driver version which allows you to connect
to a controller point to point called XIZUMIFA, which
includes FA-1/FA-1J/FA-2/FA-2J equipment)
Programmable Logic Controllers
IDEC IZUMI PLC Micro-1 Series
IDEC IZUMI PLC FA-1 Series
IDEC IZUMI PLC FA-1J Series
IDEC IZUMI PLC FA-2 Series
IDEC IZUMI PLC FA-2J Series
IDEC IZUMI PLC FA-3S/CP-11 Series
IDEC IZUMI PLC FA-3S/CP-11T Series
Read HSC (High Speed Counter) (FA-1 Only)
Write HST Preliminar Output 1 (FA-1 Only)
Write HST Preliminar Output 2 (FA-1 Only)
Read HST Preliminar Output 1 (FA-1 Only)
Read HST Preliminar Output 2 (FA-1 Only)
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=8.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 1
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=8.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 2
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=8.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 3
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=16.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 4
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=16.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 5
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=24.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 6
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=8.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 7
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=8.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 8
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=8.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 9
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=8.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 10
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=8.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 11
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Output / Digital Output
HMITalk1.DriverNumPoints = Analog Output=1, Digital Output=16.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 12
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Output / Digital Output
HMITalk1.DriverNumPoints = Analog Output=1, Digital Output=16.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 13
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=32.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 14
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=32.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 15
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Output / Digital Output
HMITalk1.DriverNumPoints = Analog Output=1, Digital Output=32.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 16
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Output / Digital Output
HMITalk1.DriverNumPoints = Analog Output=1, Digital Output=32.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 17
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=16.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 18
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=16.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 19
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Output / Digital Output
HMITalk1.DriverNumPoints = Analog Output=1, Digital Output=1.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 20
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Output / Digital Output
HMITalk1.DriverNumPoints = Analog Output=1, Digital Output=1.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 21
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Output / Digital Output
HMITalk1.DriverNumPoints = Analog Output=1, Digital Output=8.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 22
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Output / Digital Output
HMITalk1.DriverNumPoints = Analog Output=1, Digital Output=1.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 23
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Output / Digital Output
HMITalk1.DriverNumPoints = Analog Output=1, Digital Output=1.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 24
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Output / Digital Output
HMITalk1.DriverNumPoints = Analog Output=1, Digital Output=8.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 25
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Output / Digital Output
HMITalk1.DriverNumPoints = Analog Output=1, Digital Output=32.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 27
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Output / Digital Output
HMITalk1.DriverNumPoints = Analog Output=1, Digital Output=32.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 28
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=8.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 30
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=24.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 33
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Output / Digital Output
HMITalk1.DriverNumPoints = Analog Output=1, Digital Output=16.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 34
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=32.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 35
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Output / Digital Output
HMITalk1.DriverNumPoints = Analog Output=1, Digital Output=32.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 36
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Output / Digital Output
HMITalk1.DriverNumPoints = Analog Output=1, Digital Output=32.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 37
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=32.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 38
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
PROPERTY SETTINGS REQUIRED:
HMITalk1.DriverDataType = Analog Input / Digital Input
HMITalk1.DriverNumPoints = Analog Input=1, Digital Input=32.
HMITalk1.DriverP0 = Controller number (1-255). (If a 0 is entered, there will
be no previous controller selection, thus the message will
be routed to the last selected controller.)
HMITalk1.DriverP1 = 39
HMITalk1.DriverP2 = Indicates the memory address of the selected element.
[1005] DRIVER (Internal): Invalid driver stage
[1300] PROTOCOL (Timeout): No answer
[1419] PROTOCOL (Format): Missing bytes in response
[1429] PROTOCOL (Format): Unknown response
[1433] PROTOCOL (Format): Validation error in device response
[2209] CONFIG (NumValues): Too many values (max=32)
[3022] CONFIG (P0): Invalid device address (1-255)
[3508] CONFIG (P1): Invalid command
[4001] CONFIG (P2): Invalid address
[8002] CONFIG (Remote): Abnormal receive command (receive error)
[8279] CONFIG (Remote): Program transfer/write Overtime/frame error
[8280] CONFIG (Remote): Program transfer/write Read/write error
[8281] CONFIG (Remote): Program transfer/write ROM pack
[8282] CONFIG (Remote): Program transfer/write TOTAL
[8290] CONFIG (Remote): Receive data over (PLC size error)
[8291] CONFIG (Remote): Receive inhibit (PLC run error)
[8347] CONFIG (Remote): Unknown error
This driver requires that you have TAS-HMITalk 8.04 installed.
Driver Source Code Last Update: 03/08/2004 14:07:50
Driver Reference Last Update: 10/30/2008 17:40:23
© 1990-2008, CPKSoft Engineering. All rights reserved.